Features

• Universal Master - Slave interface in closed IP40 housing
• Host connection via PCI Express
• One hardware for all Real-Time Ethernet protocols
• Easy slide-in mounting without tools
• Locks and connects without additional components on the baseboard

Product Description

The universal communication module netJACK with its PCI Express interface addresses in particular the embedded market with high-performance CPUs like Intel Atom®. Alternatively, there are versions with a traditional dual-port memory and a fast serial SPI interface.

All types have the compact design of a closed IP 40 module which can be mounted without using tools. Additional costs for the device will not arise because connector and mounting rails are designed as contact areas and cut-outs on the baseboard.

netJACK can be mounted quickly and easily right before shipment - or even by the end customer.

With netJACK customers can realize the full range of communication solutions, e.g. for drives, HMI or ident systems. At the same time, additional functionalities as PLC, visualization or individual applications are possible. For customer-specific requirements, Hilscher offers a cost-optimized Design and Production Service.

Technical Details

Product	Part Number	1625.100
	Brief Description	Exchangeable Module PCI Express
Communication Controller	netX: netX 100
Integrated Memory	RAM: 8 MB SDRAM FLASH: 4 MB serial Flash EPROM
Power Supply and Current	Supply voltage: +3.3 V ± 5 % DC Typical/maximum current: 750 mA Typical power consumption: 2,5 W
System Interface	Bus type: PCI-Express, One-Lane-Port Connector type: 40 pin connector (SAMTEC FSI-120-03-G-D-AB) Pin distance/pin width: 0.45 mm/0.55 mm Transmission rate: 1,5 GHz
Communication Interface	Communication standard (protocol): Ethernet Interface type: 100 BASE-TX, isolated or 10 BASE-T (depending on loaded firmware), Half duplex/Full duplex (at 100 MBit/s if supported by protocol), Auto-Negotiation (if supported by protocol), Auto-Crossover (if supported by protocol) Connector: 2xRJ45
Diagnostic Interface	Type: USB Connector: Signal at host interface. Available only if integrated in host system
Display	Display: SYS System Status, green: RUN, yellow: RDY COM0, COM1 Communication status, both green/red TX/RX0, TX/RX1, Ethernet activity status, yellow LINK0, LINK1, Ethernet link status, green
Environment	Ambient temperature range for operation: -20 °C … +65 °C
Device	Dimensions (L x W x H): Length 62 mm (with RJ45 connector), 60 mm (without RJ45 connector), width 53.4 mm (at front panel), 50.4 mm (at body), height 25.2 mm (at front panel), 19.2 mm (at body) Weight: approx. 60 g Housing: Closed module Protection class: IP40 Mounting/Installation: Via milled footprint holes in the carrier board and retaining brackets. No mounting accessories required. Mounting/pulling cycles: max. 10
Configuration	Configuration software: SYCON.net
Conformity	RoHS: yes Reach: yes
UL Certification	UL type: cURus UL file: E334100
Conformance with EMC Directives	CE Sign: yes Emission: EN55011:2009; CISPR 11, class A Immunity: according to EN 61131-2:2003 Electrostatic discharge (ESD) according to IEC/EN61000-4-2 (Air discharge method): IEC/EN 61000-4-2:2009: ± 8 kV, Criterion A Electrostatic discharge (ESD) according to IEC/EN 61000-4-2 (Contact discharge method): IEC/EN 61000-4-2:2009: ± 4 kV, Criterion A Fast transient interferences (Burst), according to IEC/EN 61000-4-4: IEC/EN 61000-4-4:2004+A1:2010: ± 1.1 kV, Criterion A Surge voltage, according to IEC/EN 61000-4-5 (Communication and data lines): IEC/EN 61000-4-5:2006: 1 kV, Criterion A
Tests	Shock: EN60068-2-27 Ea Vibration: EN60068-2-6 Fc

 

Ordering Information

• NJ 100EN-RE/ECM V4 (1625.100/ECM V4) - Exchangeable Module PCI Express - EtherCAT Master