CS328A-XSEi

Fully configured ethernet oscilloscope - 14 bit 100 MSa/s, 2 analog channels, 8 digital inputs, External Trigger, 8M samples storage for each of the 2 analog and 8 digital channels, CS701 isolated Signal Generator (0-65MHz, Sine Wave ONLY). This is our best isolated scope, and you can use it for high performance FRA. Complete with the CS300 application software, 2 x CS1001 and CS1004/5 probe sets. The ethernet interface is fully isolated from the PC.

Cleverscope Model CS328A-XSEi is an Ethernet connected, PC hosted oscilloscope and spectrum analyser with PC based application software.
 

CS328A-XSE Acquisition Unit

• Two 14 bit analog channels sampling simultaneously at 100 MSa/sec. AC or DC coupled.
• 10/100Mbit ethernet interface
• CS700A Signal Generator (0-10MHz, Sine, Square, Triangle)
• Gain automatically set from 20 mV FSD to +/-200V FSD by choosing graph view and probe switch setting.
• Offset automatically set to correspond to the selected amplitude axis view. As an example a graph with amplitude axis of 2.40 to 2.42V automatically chooses a 20mV range offset by +2.40V - good for looking at small signals in single supply op-amp applications.
• Analog triggering of the waveform in view with a resolution of 1% of the display height. The analog trigger may optionally be conditioned with a low pass, high pass or noise filter.
• One external trigger, threshold adjustable from 0 to ±18V in 40 mV increments.
• Eight digital inputs sampling at 100 MSa/sec, threshold adjustable from 0 to 10 V in 10 mV increments.
• A dual hardware trigger system based on a rising or falling edge on any input signal, optionally qualified by a user defined digital input combination, triggering when one or both trigger conditions are met, and the time between triggers is less than, in or more than a user defined range, or the trigger count equals a user defined value.
• A rear panel I/O connector with a 100 Mbit/sec bi-directional LVDS/RS422 link, and three RS422 outputs defaulting to sampling started, trigger received and sampling stopped.
• Each channel (two analog, ext trigger and eight digital) includes 8M samples of storage, providing up to 40 ms of simultaneous storage for each channel, with 10 ns resolution.
• The sample storage may be allocated as between 2 to 3000 frames varying in size from 4M to 2000 samples. These may be used as a history store for reviewing previously captured signals, or to capture up to 3000 trigger events with a minimal inter-frame delay, while maintaining time relative to the first trigger for all succeeding frames.
• 20 MHz 5th order Anti-alias filter for improved Spectrum Analysis performance.
• Triggered LED and Power LED on the front panel.
• Input power range from 6 ~ 12V, 6W provided by a universal mains adaptor.
• Low jitter (1 ps rms) sampling clock for 70 dB spurious free dynamic range.
• Self calibration to ensure DC performance specifications are met.
• Enclosure size: 153 x 195 x 35 mm.

CS300 Application Software

• Separate, freely moveable and resizable windows to display the signal, a zoomed signal view, and the frequency spectrum of the signal, and control panel.
• The zoomed signal view optionally tracks the signal view cursor.
• Spectrum analysis with a variety of conditioning windows and display in log or linear format.
• Each signal window includes a time/amplitude tracer, and two markers for comparison purposes. Colours are user definable.
• Signal averaging (exponential, block and peak hold) and low pass filtering.
• Signal measurement, including Peak to Peak, RMS, DC, pulse width, period and frequency.
• Copy and Paste graphic or data to other applications.
• Save and Open from disk.
• User defined units, signal names and scaling (offset and gain).
• Text annotation of each graph.

CS328A-XSEi Equipment List

The following equipment is included with the CS328A-XSEi:

• 1 x CS328A-XS Oscilloscope Acquisition Unit with 14 bit 8 MSample capture and isolated Ethernet interface
• 1 x CS701A 0-65MHz Sine Wave only Isolated Signal Generator pre-fitted
• 1 x Power Supply Unit and lead
• 2 x CS1001 1x/10x 250MHz probe kit
• 1 x CS1004/CS1005 8 bit 100MHz digital input pods including probes
• 1 x ethernet cable
• 1 x CD that includes CS300 Application Software, CS328A User Manual, sample files, videos and white papers